The Farmall Cub is the smallest tractor in the International Harvester line, capable of pulling one 12-inch bottom plow. Production began in 1947 and continued relatively unchanged until 1964. Variations of the tractor (International Cub Lo-Boys) were continued for some time after that. The Cub was the only Farmall built with an L-head engine.

Farmall Cubs built in different years can be found with McCormick-Deering, Farmall, and International Harvester decals, depending upon the configuration of the parent company International Harvester in the year of production. For the purpose of this article, we will refer to the tractor as simply a "Farmall Cub".

This little tractor was aimed at the needs of the small-acreage farmer - farms of 40 crop acres or less and truck gardens, or for larger farms that needed an extra tractor. Seven or eight implements were initially designed for it: Plow, Disc, Backblade, Sickle-Bar Mower, Belly-Mower, and a one-armed front-end loader for starters. Like the Farmall Model A, the Cub was off-set to the left with the driver and steering wheel on the right. This concept was called "CultiVision" in reference to the ability of the driver to have a perfect view of a belly-mounted cultivator. In 1947, the Farmall Cub sold for around $545.00 - attachments and implements were extra.

The Farmall Cub was easily one of the most popular small chore tractors made in history. This is shown by the sheer numbers of Cubs that were built. People would not stop buying them! With a production run lasting almost 20 years, over 200,000 of them were built between 1947 and 1964.

Article Courtesy of YT Mag.

Classic Farmall Tractors: History, Models and Variations
From the first tractor built in 1924 to the last Farmall model to roll off the line, this richly illustrated history tells the full story of Farmall tractors and fills in a key chapter of American agricultural? history.

A Brief History of the Farmall Tractor
In 1923 American Farming would change forever.Enter the Farmall. The first Farmall Tractor produced by International Harvester (IH) was released only in Texas because the people in IH were not sure the tricycle type tractor would be.

The Farmall Cub Tractor
Built with an L-head engine, the Cub was the smallest tractor in the International Harvester Line. The 1947 base price was $545.00. The Farmall Cub was possibly the most popular small job tractors in history as shown by the quantity of.

Farmall Tractors F Series
The Letter series of Farmall tractors was produced until 1954, and was a defining product line in the history of International Harvester. 

Technorati Tags: 350, 450, a, c, cub, farmall, h, harvester, history, international, m, mccormick, mta, on, super, tractors

These days, as well as going to a reputable dealer or looking in the classified ads of your local newspaper, there are many tractors to be found on ebay. If you would, you can also find many used Farmall Tractors listed here.  The Farmall-A was introduced at a factory preview in Chicago many years ago and it is the International Harvester company that produces the smallest tractor in its thirty-one years of manufacturing.

This tractor has become so popular because of its all-purpose power unit with complete implement equipment available to farmers, making farming a lot easier even on small farms in the United States and around the world. This little machine will also do a lot of work on larger farms, supplementing larger tractors in lighter operations.

This tractor is available only with rubber tire equipment. The weight is approximately 1700 pounds, this is probably less weight from flywheels than on some earlier models. The Farmall-A has become an impressive tractor after seven years of development by the manufacturers so any farmer choosing to purchase one will no doubt have a fantastic and reliable machine.

The tractor was built to endure any type of work in farming regions of the United States and all over the world. It is suitable for working in hilly areas, corn fields and even cotton lands. It will withstand every type of possible condition that a tractor could be needed for.

The new Farmall-A has a lot of new features that will please many farmers. The most obvious one to the farmer would be the offset positions of the seat, engine and transmission train. To benefit the operator, the engine is offset nine inches to the right, while the seat is offset at the same distance to the right. Setting the seat and engine at these positions gives the operator an unusual area of vision.

Giving the operator this clearer vision helps greatly while doing row crop work; this is described as ‘Culti-Vision’. This can also help to offer a desirable balance whilst plowing, which is normally approximated by unequal weighting of wheels. This feature is claimed by many farmers to be of great value, especially to growers of cotton, corn, vegetables and many other crops planted in rows requiring cultivation.

The best tractor or machinery that any farmer can acquire to make life a little easier around the farm is greatly appreciated, as farming life is not only hard and difficult work, it is also year round work through every season. To have features like this on a tractor makes life a lot easier for the operator. To pick up a used Farmall tractor that was built when new additions were added is like finding gold. The seating itself is a luxury to the operator, no more sitting in cramped positions.

To buy a used Farmall tractor is a great choice as these are a superb piece of machinery with a choice of purchasing added implements to make farming life that much easier. Remember, when buying a tractor, that it has to last a long time, so make sure the body is in good condition, farmall tractor parts can always be purchased.

By: Mimilisan

Article Directory: http://www.articledashboard.com

——-
Irwan is an owner of Used Tractor Supply Site Visit his website to find john deere tractor, kubota tractor, farmall tractor, massey ferguson tractor, tractor information and other farming equipment guide.

Older Farmall Tractors are Good Value
First-time buyers of Farmalls can be enchanted by the myth and mystique, but you should check a few things before you buy a venerable H or Cub. Yes, they cost less than buying new, and they do the job.

The Farmall C Tractor
Serious antique collectors know about International Harvester’s Farmall tractors and the lasting impression they made on farmers across the US and abroad. One Farmall model that definitely made a mark on American farming history.

The Farmall M Tractor
Considered one of the most dependable tractors in farming history, International Harvester started production of this farm tractor in 1939. It released many variants over the 14 year production of this tractor, namely MD.

Farmall Tractors for Sale-Tips on Getting the Best Deal
Farmall tractors , especially Cub Farmall Tractor and the Farmall H Tractor have proven their worth as tough worker farm machines tested in many countries under all kinds of seasons. While tractors were primarily used in farms.

Farmall H tractors sighted in Lower Delaware!
The Delaware beaches and you keep your eyes pealed you’ll see a set of farmall H’s and Cubs in mint condition in an open shed right about 50 feet from the highway. It blew my mind to have such prized tractors right near the highway.

Farmall Tractors Are My Love
I love the Farmall. And own a piece of Americana. While driving up through Sussex County near the Delaware beaches recently, I spotted a lone Farmall Tractor, I think it was a venerable H, rusted and vine covered near a dilapidated soy.

Technorati Tags: 250, 450, a, c, cub, farmall, for, h, hand, harvester, international, m, mccormick, mta, sale, second, super, tractors, used

Farmall tractors are truly impressive machines. Whether you choose to buy a new or used one, a good choice of machinery has been made. There is nothing wrong with buying a used or second-hand tractor, providing you know exactly what you are looking for. These days, as well as going to a reputable dealer or looking in the classified ads of your local newspaper, there are many tractors to be found on eBay. 

The Farmall H was introduced at a factory preview in Chicago many years ago and it is the international harvester company that produces the smallest tractor in its thirty-one years of manufacturing. This tractor has become so popular because of its all-purpose power unit with complete implement equipment available to farmers, making farming a lot easier even on small farms in the United States and around the world. This little machine will also do a lot of work on larger farms, supplementing larger tractors in lighter operations.

This tractor is available only with rubber tire equipment. The weight is approximately 1700 pounds, this is probably less weight from flywheels than on some earlier models. The Farmall-H has become an impressive tractor after seven years of development by the manufacturers so any farmer choosing to purchase one will no doubt have a fantastic and reliable machine.

The tractor was built to endure any type of work in farming regions of the United States and all over the world. It is suitable for working in hilly areas, corn fields and even cotton lands. It will withstand every type of possible condition that a tractor could be needed for.

The new Farmall-H has a lot of new features that will please many farmers. The most obvious one to the farmer would be the offset positions of the seat, engine and transmission train. To benefit the operator, the engine is offset nine inches to the right, while the seat is offset at the same distance to the right. Setting the seat and engine at these positions gives the operator an unusual area of vision.

Giving the operator this clearer vision helps greatly while doing row crop work; this is described as "Culti-Vision". This can also help to offer a desirable balance whilst plowing, which is normally approximated by unequal weighting of wheels. This feature is claimed by many farmers to be of great value, especially to growers of cotton, corn, vegetables and many other crops planted in rows requiring cultivation.

The best tractor or machinery that any farmer can acquire to make life a little easier around the farm is greatly appreciated, as farming life is not only hard and difficult work, it is also year round work through every season. To have features like this on a tractor makes life a lot easier for the operator. To pick up a used Farmall tractor that was built when new additions were added is like finding gold. The seating itself is a luxury to the operator, no more sitting in cramped positions.

To buy a used Farmall tractor is a great choice as these are a superb piece of machinery with a choice of purchasing added implements to make farming life that much easier. Remember, when buying a tractor, that it has to last a long time, so make sure the body is in good condition, spare parts can always be purchased.

Author: Irwan H Nuswanto

Irwan is an owner of Used Tractor Supply Site Visit his website to find john deere tractor, kubota tractor, farmall tractor, massey ferguson tractor, tractor information and other farming equipment guide

Article Source: http://EzineArticles.com/?expert=Irwan_H_Nuswanto

Farmall H Tractor Parts
If you’re wondering where to find farmall tractor parts for use on your machine then look no further.  Here you can find the biggest selection of parts and tractors available at reasonable prices and for all models.  I found a camshaft for my Farmall H.

Finding Farmall Tractor Parts
The last Farmall of any kind rolled off the assembly line in 1975, and the 5000000 th Farmall was the end of an era. But folks like us, who see them against a field of golden grain and blue sky remember why the Red Farmall was symbolic.

Lawn tractor parts and Garden tractor parts.
And to maintain it, you need a Good Lawn and garden tractor parts. You can get it according to your needs and interest. There are lots of Lawn and Garden tractor part manufacturers these days, So No Worries.

Technorati Tags: camshaft, cheap, engines, farmall, h, international harvester, old, operators manual, part, parts, spares, tractor, tractors, used

If your thinking of buying a used tractor have a look at the following checklist to help you to find the best fit from a selection of used tractors. Here is a list of features that you need to consider when searching for a used tractor.

Horse Power - Does the used tractor that you are looking at have enough horse power to perform the job that you require it to do. Allclass equipment have may different used tractors with different horsepower’s for you to browse. Click here to see our current range.

Tyres - Its important that the tractor that you are looking at not only has the required tread pattern for your required purpose but that it is not at the end or close to the end of its useful life. If your used farmall tractor has only a fraction of wear left in the tyres it’s an added expense for you to bear in the future. Please ask your used tractor consultant how much life there is in the tractors tyres.

Engine hours - Most used tractors have a long and useful life. You can get an idea of how much life is left in the tractor of your choice by looking at the engine hours. The engine hours will help determine a fair price for the used tractor that you are looking at as the more hours that it has the cheaper it generally is.

Age - the age of the tractor will also determine the price of the tractor to some extent. Obviously if two tractors are the same age you would refer back to the other areas to determine what was the best deal.

History - It’s always good to know the history of the used tractor and the type of work that it was involved in in its previous life. This will help you to determine if it will be a reliable machine in the future.

Make and Model - Some makes and models attract buyers more than others. Some makes attract a premium because of their reputation for quality and reliability while others may have certain characteristics that may not be desirable for the job that you are doing. Always check with your used tractor consultant to check if there is anything about the model that you are looking at that may not be good for your application. The Farmall Cub will be best used for a specific farm job and the Farmall 450 may be better suited to another role, so its always best to check!

Cabin - Because your tractor is your office you need to make sure that you are comfortable working within the cabin. Does it give you the level of comfort that you are used to or need? Is there easy access to all the controls, does it have air conditioning, and any other features that you require?

4WD - 2WD - Do you need a 4WD tractor? Is your new used tractor to be used for an application that is in a location that necessitates 4WD or will a 2WD tractor be sufficient. If you don’t need a 4WD tractor then its pointless to pay the extra cost so make sure you are clear what the tractor might be doing in the future so that you know which option to choose.

You should take all these factors into consideration but make sure that you ask our specialist Used Tractor consultants for their feedback on your application and needs. They are experienced at matching quality used tractors with new owners. Contact us now about your needs or view our catalogue of tractors online.

By: Andrew Moore.

Article Directory: http://www.articledashboard.com

Author Bio Andrew Moore is an expert mechanic in evaluating used excavators & loaders, engines & generators for excavators and tractors, buy used tractors, excavator attachments, mowers, Toyota skid, kanga loaders, beeline technology.

Farmall Tractors for Sale
Farmall tractors , especially Cub Farmall Tractor and the Farmall H Tractor have proven their worth as tough worker farm machines tested in many countries under all kinds of seasons.

Old Vintage Tractors For Sale
Old vintage tractors are small, light machines that are designed to maintain domestic lawns and gardens. Most tractors have two cylinder engin es, up to 23 horsepower for the bigger machines.

Yanmar tractors for sale
Yanmar tractors are extremely sturdy and trustworthy. In todays economy farm owners cannot afford to be buying tractors on fly. A great tractor needs to be able to stand up to the elements and the abuse of everyday wear and tear.

Antique Tractors For Sale
There are many informational websites on this area, and some of these also offer antique tractors for sale. If you are looking for a working yesterdays tractor, your checklist of research questions should include the following.

Technorati Tags: 140, 450, a, antique, buy, cub, equipment, farm, farmall, farming, for, h, m, machines, mccormick, mta, old, purchase, sale, super, tractors, used

Because you are reading this article, then its obvious that you have an interest in vintage tractors. Maintaining, collecting and refurbishing vintage tractors from days gone by has become extremely popular recently. There are numerous reasons for this; firstly they are relatively low-cost to invest in, and look after and sometimes they cost less than the road tax on a new tractor. Also, they are still of use when it comes to doing work. They are simple and understandable. Each tractor has its own history and can be restored to bring pride and a great deal of enjoyment to the restorer. But how do you know how to buy the right tractor and how do you go about it?

Antique tractors come in many shapes and sizes. , you should understand your needs as this will determine what you look for. You first need to know your needs you then need to convert this into a list of requirements this will then enable you to make a better decision when it comes to buying your antique tractor.

Depending on whether you need an old tractor for your or you are intending to begin restoring as a hobby you will choose different machines. Many people will tell you that some of the most sought after vintage tractors make poor day to day tractors and on the flip-side painstaking restoration of an very popular tractor may not be worth the effort (not to mention the cost of that perfect original paint mix).

No matter which type of tractor you are looking for, you should always start your search with some detailed research. Many research books are available that have this information giving you endless details about any tractor model you wish. While collect ability, hitch system, etc make up the criteria for choosing what size, type, manufacturer, or model of tractor you want, a more straight forward set of factors must be used for selecting the specific tractor you will purchase. As always, restoring an antique collectible tractor will have a completely different list of criteria.

Antique Tractors Bought for Working
Those that need a machine for working their farm are in a better position to get what they need quickly but it is amazing how many people buy the wrong type of tractor and become disillusioned with old machines. One of the frst things you should look at is the layout of your fields, how hilly is it and also what type of farm machinery you will need to use. If you plan on using the tractor for tillage, such as barley or corn, then you should consider a Nuffield M4, a Nuffield 1060 because other machines may be too low to the ground and cause damage to your crop. On the other hand if your land is mountainous, you may need to consider something like a Massey Ferguson 35X or a Massey Ferguson 168 Orchard Tractor or a Farmall Cub. If you are going to use machinery, you should first understand the horsepower requirements of this implement and make sure the tractor you select has the right weight and the correct horsepower to do the job. If, for example you will be using a ten foot disk harrow, then you will need more power than a Fordson N Thorough basic research will ensure that you don’t make these basic mistakes.

Once you have selected your model, don’t pay much attention to the look of the tractor, the basic mechanics of the tractor should be the first thing you focus on. Many good day to day tractors will not have seen paint in years and will have been patched up and mended with a range of strange materials.

Make sure that your tractor performs all the basic tasks properly, so check the steering, gears, forward and reverse, PTO, lift, lights, indicators and hydraulics. Even if you plan to work on it straight off, you may not be interested in a complete restoration for sometime and need to keep to a minimum the number of initial jobs. You should have a detailed check list which included at a minimum the following: does it start easily from cold, run well when hot, all the electrical components work well, does it have good traction If possible you should go to your test armed with a toolbox containing a compression tester, expensive Fluke digital multimeter, hydrometer, and other specialty tools. or bring somebody with you who has these tools.. If you are not lucky enough to have access to these tools, as many dont then don’t panic. You should in this case rely on your own common sense and your own observation skills.

However, having said this, you should still be armed with the a basic knowledge on the operation of the tractor you are planing to buy. You should, at a minimum beg, borrow or steal a copy of the owners manual for the particular model of tractor you are planning to inspect so you are familiar with its operation and basic specs and what to look out for.

Here is a basic checklist which you can use with any vintage tractor:
Does it start easily? - A tractor that starts easily may rule out several items in one go Good Battery, compression, ignition wiring / magneto, tune up, fuel flow, Carburetor can be assured (not guaranteed) by this. If it doesn’t start easily from cold, it still may be a good machine but you will have to spend some time and money on it. One thing you should be watch out for is if the tractor is out and warmed up when you arrived, you lose an important checklist item, namely the cold start, because as we all know a warm engine starts much more easily then a cold one..

How does it run when warm - Getting it hot is a must if you want to find out how it will work after you plowed the first row. There are simple and complex problems that can cause the tractor to run poorly after it warms up. You should run it for al least half an hour. After running look for leaks, antifreeze and both oil. Then, shut it down and see how it starts up again.

Are the brakes working well - Although relatively inexpensive to replace, they are difficult to get at on many tractors and will require extensive teardown to get the new ones in. You can test the brakes by locking one wheel and cranking the steering to that side. The tractor should spin and the wheel should not rotate, do this for both wheels.

Does it generate a lot of - like rings, pistons, or valve guides. Black or white smoke can oftentimes be sorted out with carburetion or ignition changes but still represent work.

Does it make clunking noises from inside the engine - A simple ticking from the top of the engine may be a simple valve adjustment but a deep thunk from the bottom or middle of the engine would indicate very serious and expensive repairs. The clunk should be more pronounced under load conditions. This may be a sign of problems with the crankshaft, bearings, or piston rods. And mean a very expensive repair job.

What condition is the oil in - After you have run it for a while, turn off the engine and check the oil for foaming or presence of water. This is a big problem.
Is there head leaks - look for signs that oil are seeping out the head gasket. If the tractor is encrusted with grease and dirt, it may cover obvious signs of seepage.

Is the clutch working well - a clutch is not that costly to fix but splitting the tractor in half is beyond what most collectors want to do.
Check the Dynamo - There should be a little charge indicated on the ammeter as the engine is turning over and a change in the charging level when the lights are switched on (this shows that the resistor or regulator switch and cutout is working fine). At normal running speed, no release should be displayed.

Work the hydraulics - Check the full range of the power rams by extending them with a load. Let the load stand in the hold situation for a period to be sure that there is no breakdown. Chattering noises from the pump while lifting indicate the pump is not getting enough flow of hydraulic oil. The pump may have experienced excessive wear when run this way for long periods of time and may be ready to fail.

Look for structural cracks - It takes a bit of time but it is well spent. Look for hairline cracks in all the steel components. While not expensive to repair, it’s just another time consuming job. In addition it means that your tractor can not be used until this problem is fixed..
IF initially the tractor fails some of these areas, you may be able to knock down the price (since you found all the problems). At this point you must determine if you have the time to correct what you discovered… and make savings. If your tractor needs are time-critical, run a mile from this tractor.

The best option for buying a working tractor is either to buy one that is still in use (but the owner needs to upgrade) or from a reputable dealer. The first category is commonly someone just like you who needs a tractor on a day to day basis. These transactions are usually enjoyable and can even spark a long term friendship that goes beyond the buyer/seller aspect. This type of person will probably even let you try the machine with on your farm and tell you all those things they would repair if they were keeping the tractor.

Buying from dealers can also be a good idea but even at a dealer you should be armed with your evaluation criteria rather than relying on "the warranty". Even if your dealer includes warranties, hauling a tractor back for even free repairs will list you a lot of time and effort. Also remember that the dealer is there to make a profit for his business and may not have your best interests at heart. So buyer beware!

While many of the above experiences may sound a bit negative, you should do your background research and understand the particular issues a tractor may have before you invest.

By: Asker Dough

Article Directory: http://www.articledashboard.com

Asker Dough is a long time net entrepreneur and has founded YouTractor.com which offers exclusive tractor videos of antique tractors and modern muscle tractors.

Farmall M (grader)
I just got back from the woods this morning from visiting my Farmall. It is kinda sad.It has been abandoned for about 30 years. It has only been protected by a tarp.For the most part it seems complete and solid.

Farmall M Starter Tips or Schematics
I am going to replace a farmall m starter and am wondering if anyone has any schematics of the starter/ tractor/ electrical etc.. If you dont, do you have any tipe, I have only done starters on riding mowers and compact utility tractors.

Farmall M with quick attach bucket
Here are some pictures of my 1941 M with a quick attach for the bucket that I made. I made it so that I can hook up to bobcat attachments.

Technorati Tags: blade, buy, cylinder, engine, farmall, find, grader, m, manifold, old, order, parts, point, sale, seat, spares, tractor, tractors, used, wiring

The decision to purchase a used tractor can be confusing as there are so many different models to choose from and equipment options. It is probably best, in the beginning, to write a list of what exactly you require the tractor to do and what added equipment to you need exactly. If you are using a typical tractor for general use on a small farm, here are a few guide lines.

It all depends on what you need the tractor to do, as there can be a lot of difference between tractors. For instance, if you wanted one that will power a snow blower on a driveway roughly a quarter mile, or for mowing an acre of land. General farm use tractors are always needed for plowing so it’s what size tractor to choose; a two plow or three plow. This means the tractor can pull a two bottom or a three bottom plow sufficiently.

The soils on your land can also make a difference when choosing a tractor. Heavy clay soils or hills will require more power from the tractor; a two or three plow tractor has tilled many a Midwest farm. A good example to consider is it takes about 15 horsepower per bottom, so it would probably take 30 horse power for a two plow and 75 horse powers for a five bottom plow. By using different implements, these will use varied amounts of power.

Finding something that works well with a round baler may not be adequate for a small square baler; grinding feed can use a lot of power while harrowing a field can use a lot less power. Some would say the ideal thing to do is purchase your tractor first, and purchase implements based on the capabilities of your tractor. Make sure you have researched to buy the best tractor for your needs.

To buy a tractor, have you considered what machinery you would like the tractor to power. If you would like a hydraulic loader, look at tractors with dual hydraulic connections. Hydraulic hook ups, when using other implements can be a necessity, so look out for a dual remote one.

Never consider a tractor that does not have a power take off, (PTO). You may find that it is older tractors that do not have this. The most common was 540rpm but now more implements are using 1000rpm. Since the 1960s, many tractors were produced with both speeds. 1950 models had a live power take off which means it continued to run after the clutch was pushed in. Tractors before this made it hard using a mower, combine or corn picker because when the clutch was depressed everything stopped.

A similar principle to this is live hydraulics, this works when you depress the clutch the hydraulics controls still function. Many loader tractors can be used without this and the reverse is many think this is a great feature when using a loader; personal opinion, really. The older tractor had a one way hydraulic system; this system would lift and then rely on gravity to lower equipment. Cultivators, plows and mowers are just a few pieces that used this system.

When deciding to purchase a tractor, age, model and brand can play a huge part. If deciding to buy an older model, are the parts still available when needed. It’s pointless having a tractor if, when something needs replacing, you can no longer buy it. Parts can be expensive enough, as with any machinery, without having to nearly pay double if your dealer has to pay shipping expense to purchase the part you require. The longer this takes, the longer your tractor is out of action.

By: Mimilisan

Article Directory: http://www.articledashboard.com

Buying a used Tractor?
What are the right questions to ask when buying a used 55 HP +/- tractor for a farm? Take someone along that is knowledgable about tractors like an old farmer… it will prove invaluble beyond just asking questions for yourself.

Finding Farmall Tractor Parts
The last Farmall of any kind rolled off the assembly line in 1975, and the 5000000 th Farmall was the end of an era. But folks like us, who see them against a field of golden grain and blue sky remember why the Red Farmall was symbolic.

I’m Looking To Buy A Tractor
I speak of a tractor part of a tractor-trailer combo such as a peterbilt model 379-127 etc. Sample ratios are "4.10", "2.79", "3.55" etc. That is the gear ratio of the rear ends. Also called the final drive ratio.

Technorati Tags: 450, a, antique, buy, buying, c, cub, equipment, farmall, for, h, m, machinery, machines, old, order, parts, sale, tractors, used

None of us wants to feel we have made a poor decision on an investment as large as buying a used tractor, but many of the checks you ought to make and research you should do are no different from those you would make anyway. For example, you may already have a brand name of tractor that you have owned before or feel confident in and know to be reliable. All the big brand names are available online; John Deere, Massey Ferguson New Holland, Case IH and others such as Farmall can all be found.

Before you opt for what seems like a bargain it’s wise to check that spare parts are not prohibitively expensive for that model and that maintenance services are available reasonably near you. You would also want to know the age of the vehicle, how many hours are on the clock and the book value of the tractor in relation hours of use and age. If it seemed incredibly cheap you might want to ask further questions regarding its maintenance record, general condition and whether it is due a major service.

Whilst online photos cannot tell you everything about a tractor they ought to give some visual sense as to how well a vehicle has been treated and its general condition. When weighing up all these factors you can trust your instincts; if you have doubts then ask more questions and demand clear evidence of age and usage before you make your decision.

If you can buy locally you may strike gold in that you can pay Internet prices, generally lower due to reduced costs, and get a good look at your tractor first. You can then see it running, have a go on it and check out any rattles, bangs or excess smoke. If you aren’t mechanically minded, try to take someone with you who is. Even if you have to pay them, it may save you money in the long run if they spot a fault.

One big advantage of the Internet is that your field of choice is widened hugely. If you spot your tractor of choice at a price you like being sold elsewhere in Europe then, after checking the back load transport costs, you may well find you still save money compared to what is available more locally; prices may be cheaper in other countries. You may have concerns about buying online from a distant place without directly seeing your vehicle it can help to look for good transparent honest information on the online advert as a guide to the integrity of the seller, and again weigh up all the factors.

If it seems cost effective given time off work and travel, you could still go and see it. If you do your homework and buy the best tractor you can afford, then you stand a decent chance of landing yourself a good deal online.

By: Robert Tate-4587

Article Directory: http://www.articledashboard.com

Old And Used Are Still Good
Used tractors, second hand farm equipment, used farm equipment, and other discounted machinery are advertised in classifieds, auctioned or sold by individual farmers. But to be sure, it’s best to buy your used machines from established websites.

Considerations before Buying New or Used Tractors
A tractors is a farm machinery that is used in the preparation of land and during planting. Buying a tractor can be quite challenging if you do not know how to get a good one. A good tractor is that h.

"Oh for Two", or "How Not to Buy a Tractor"
Of course I have been looking for another Farmall 450 or at least a good complete engine, but so far I have yet to find any that I can look at right now or that fit my bill. In the meantime I decided to look at a few other tractors.

Technorati Tags: buy, buying, county, cub, equipment, farm, farmall, for, how, in, machinery, machines, NC, parts, sale, spares, tips, tractornew, tractors, used, york

Antique Garden Tractors are small, light machines that are designed to maintain domestic lawns and gardens. Most tractors have two cylinder engines, up to 23 horsepower for the bigger machines. Antique Garden Tractors are not for a fenced-in yard because their decks will never get past the standard 36 inch gate. These heavy duty machines are perfect for lots with two or more acres to mow. Antique tractors are machines after all! Proper care must be taken while operating the system, to keep ourselves safe and our good investment safe as well.

Garden tractors are generally capable of mounting other implements such as harrows, cultivators, sweepers, rollers and dozer-blades. Like ride-on mowers, antique garden tractors generally have a horizontally-mounted engine with a belt -drive to a transaxle -type transmission (usually of 4- or 5-speeds, although some my also have two-speed reduction gearboxes. Antique tractors are like full-sized pickup trucks. The wheels and tires are larger, the ground clearance is greater and the frame and front axle are heavier.

Old Tractors are excluded. Tractors per 1000 Hectares of Cropland are calculated by WRI by dividing the number of tractors in use by the total hectares of arable and permanent cropland. Antique Garden Tractors aren’t cheap, but well worth the investment. You will pay between $1,500 and $3,000 depending on the model you purchase. They are usually designed primarily for cutting grass being fitted with horizontal rotary cutting blades. The distinction between a garden tractor and a ride-on lawnmower is often hard to make- generally antique garden tractors are more sturdily built, with stronger steel frames, axles and transmissions.

Antique Garden Tractors are designed to be strong enough for use with plows, tillers, snow blowers, etc. Antique Garden Tractors are perfect for lawns or gardens that more than one third of an acre. The difference between a garden tractor and a riding mower is that Antique Garden Tractors generally have larger tires and they have more power and are usually designed primarily for cutting grass being fitted with horizontal rotary cutting blades. The distinction between a garden tractor and a ride-on lawnmower is often hard to make- generally antique Garden Tractors are more sturdily built, with stronger steel frames, axles and transmissions.

These antique Tractors are not fitted with ROPSs, although they, too, can overturn on steep terrain or with faulty loading. An important safety feature on any tractor is a PTO guard, designed to prevent clothing or hair from catching on the turning shaft. They are primarily mowing machines, powered by ten to twenty horsepower air-cooled gas engines, although a few are available with diesel power. The larger models have hydraulic rockshafts, auxiliary hydraulics for snow blades and throwers.

Lawn tractors are just small tractors. Most people find it very relaxing and rewarding to restore and collect these made in America small tractors. Antique Garden Tractors are versatile pieces of equipment. It can do a slew of jobs as mowing, tilling, lawn rolling, lamppost hole digging, and many other jobs.

By Andre Brown Published: 9/30/2008

Old And Used Are Still Good
Used tractors, second hand farm equipment, used farm equipment, and other discounted machinery are advertised in classifieds, auctioned or sold by individual farmers. 

Find Used Tractors And Excavators Online
A used Excavator can cost you less than half of what a new one would cost and be available to you at any time. Buying a used tractor or used excavator by searching online is really the easiest and the best thing to do.

How to Buy a Used Tractor and Save Thousands of Dollars
The secret to getting a great deal when buying a used tractor is to be armed with information. Start by knowing how to quickly determine the age, condition and average selling price for any brand and model of used tractor.

Top tips for Buying Used Tractors
If you are thinking about purchasing a used tractor it is very important to know what you are looking for so that you are able to select the ideal tractor from the vast number of tractors that are available.

Technorati Tags: 140, antique, buy, farm, farmall, find, for, j, land, machine, manual, old, operators, part, parts, plough, plow, sale, tractor, tractors, used

A used Excavator can cost you less than half of what a new one would cost and be available to you at any time. Buying a used tractor or used excavator by searching online is really the easiest and the best thing to do. Going to a dealer close by would mean only information regarding a particular brand. However, in the online world you can make immediate comparisons on the features, price and other aspects of the very best brands. You are sure to get the best possible deal online.

When it comes to buying used tractors and buy used Excavators online, there are a few things that you need to consider prior to the purchase. Firstly, the present condition of the machinery is a very important criterion that would greatly influence your decision. Ascertaining the condition of the machinery, its useful life and efficiency is of utmost importance. Although you have several options online, finding a reliable seller or dealer is really important. It is best to buy from a reputed and reliable dealer. This way you are sure of the quality of the product.

Getting the documents checked is another important to do on the list of things. Only then can you be sure that the machinery you are going to buy would serve you rather than the other way round. The hours of use, the maintenance of the machinery and its overall condition is all to be ascertained before signing on the dotted line. It is also important that you do check the availability of the spares. Servicing facilities, the network of service centers and the cost involved is also an important consideration.

Keeping your eyes and ears open for any and every information is the key. You need to gather as much data and information about the machinery and the dealer. Making verifications regarding the smallest of details would ensure that you have a good deal. Value for money is the basis for your purchase decision and thus, every effort must be made to strike the right and the best deal.

The online world is the best place to find used tractors, Excavators and other machinery for a fabulous price. All that is needed is a good survey, gathering relevant information and making the right decision. A right purchase would actually stand you in good stead for a really long time to come. Buying a used tractor or a used Excavator is no small addition to your business, thus, it is important that you take time and effort to make an informed decision.

By: Andrew Moore.

Article Directory: http://www.articledashboard.com

Author Bio Andrew Moore is an expert mechanic in evaluating used excavators & loaders, engines & generators for excavators and tractors, buy used tractors, excavator attachments, mowers, Toyota skid, kanga loaders, beeline technology.

The Farmall Cub Tractor
Farmall Cubs are restored and used in local parades. Though not rare as antiques, their popularity commands a high purchase price from $1000.00 to $3500.00 for a running tractor, depending upon condition and available implements.

Older Farmall Tractors are Good Value
Once I used my Farmall H to pull my neighbors Lexus out of a mud ditch that had collected after a storm. It looked cool pulling the black Lexus, and I’m glad it looked polished red and perfect.

Why choose used farmall tractors
These days, as well as going to a reputable dealer or looking in the classified ads of your local newspaper, there are many tractors to be found on ebay. if you would, you can also find many used farmall tractors listed on this site.

Case IH Celebrates 85 years of Farmall
Farmall is celebrating 85 years of service for the American Farmer. The first tractors were built in 1923. The Farmall was built for row crop farming. The Farmall regular was designed to use implements fore and after.

Technorati Tags: 560, a, air intake, antique, c, cub, diesel, farmall, h, m, manifold, old, parts, pulling, super, tractor, used

Yesterdays tractors’ famous brands including Allis Chalmers, Brown, John Deere, Farmall, International Harvester, and Ford can all be found "alive and kicking" if you know where to look and what to look for. These and other yesterdays tractors can be found alive and well even if they were manufactured before 25 years ago, before 40 years go, even back into the 1930s.

If you are looking to buy one, the internet is probably your best bet. You may find tractors at local dealers, but to get a good price on the tractor that you want, you should try an online search for yesterdays tractors or yt tractors on your favorite search engine.  Before you begin your quest to buy your first yesterdays tractor, you want to define your own personal needs and desires first. You cannot make an informed buying decision about used or antique tractors without knowing why you want them in the first place.

For instance, it helps you to understand that many of the yesterdays tractors that are the best for someone interested in the pleasure of restoration are not those that are in the best interests of those who are investing in their professional farm machinery.

So, once you have made up your mind as to why you want your tractor, you will want to get hold of research books or talk to experts in the tractor industry to find out which tractors are the best fits for your more detailed personal goals as well as your personal style–although it probably goes without saying that if you are looking for a great buy on a working tractor, mechanics means just about everything and looks mean next to nothing. There are many informational websites on this area, and some of these also offer antique tractors for sale.

If you are looking for a working yesterdays tractor, your checklist of research questions should include: how easily does it start up?; how does the engine sound (smooth and quiet or clanky)?; do the brakes and hydraulics work with precision?; can it "run hot"?; how is it with smoke or pollution?; does it throw a lot of oil or other liquids?; how does the body of the tractor look from the perspective of soundness?

If you are a collector or restorationist, you will want to research different elements of your possible yesterdays tractors.

One thing to consider and check deeply into is the rarity of a tractor, especially if you want to create a collection or restore a model that is highly unique or very valuable financially.

But unless you have your heart set on a particular model for highly private or nostalgic reasons, you should avoid getting overly enthused over a possible great find before you have as many facts as can reasonably be expected, so that you don’t waste money or time.

Also make sure you research how easy or difficult it will be for you to find the tractor’s add-ons or other hardware. Whether it’s for work or pleasure, owning a yesterdays tractor can be exciting and satisfying.

By: F. Roaldset

Article Directory: http://www.articledashboard.com

antique tractors for sale

The Farmall Cub Tractor
Farmall Cub began in 1947 and continued relatively unchanged until 1964. Built with an L-head engine, the Cub was the smallest tractor in the International.

Safely Transporting Farm Equipment
Wheather you are transporting a antique tractor or farm equipment from field to field Safety is number one. Each spring the rural countryside blossoms with a wealth of moving farm machinery as farmers begin transporting machines from field to field.

How to buy a tractor and get a good deal
You could perhaps get a garden tractor or maybe you would prefer a compact tractor. Garden tractors are a type of tractor which is actually a lawn tractor which is built heavier so that it is able to cope with the bigger work load.

Technorati Tags: antique, buy, farm, farmall, for sale, international harvester, machinery, old, parts, purchase, tractors, used, vintage, working